Popcorn Ceiling Removal in Port St. Lucie, FL
Popcorn ceilings are common in Port St. Lucie homes built before 2000, particularly in the older sections of Torino and the original Gatlin Boulevard neighborhoods developed in the 1980s and 1990s. KB Painting & Refinishing removes popcorn texture, repairs the underlying drywall, and applies a smooth or lightly textured ceiling finish — all with our own crew and a five-year workmanship warranty on the finished surface. We test for asbestos before any scraping begins, which is required by Florida law for homes built before 1980.
Local insight
Older Port St. Lucie homes near the Torino neighborhood and the original US-1 corridor were built during the popcorn-ceiling era, and many still have the original texture. Florida's humidity tends to stain popcorn ceilings faster than in drier climates — water intrusion from roof leaks or AC condensate drips leaves rings that popcorn texture makes nearly impossible to spot-repair.
Popcorn ceiling removal in Port St. Lucie
Homes built in Port St. Lucie’s earlier residential phases — particularly in Torino and neighborhoods east of US-1 developed in the 1980s — often retain their original popcorn texture ceilings. The texture itself isn’t structurally harmful, but it collects dust, stains easily from humidity and AC condensate, and makes any water damage immediately visible as a spreading brown ring that can’t be painted over cleanly. Removing it and finishing to a smooth or knockdown surface solves all three problems at once.
The removal process is straightforward when the drywall underneath is in good shape, but Port St. Lucie homes with a history of roof leaks or bathroom moisture intrusion often have soft spots or tape failures hiding under the texture. We inspect the drywall condition before starting and include minor drywall repair in our standard scope — you won’t get a flat ceiling with a patch bump where the old damage was.
Our process
We begin with a moisture test of the ceiling surface. Dry popcorn scrapes cleanly; wet texture becomes a paste that damages the drywall paper underneath. If needed, we wet-scrape in small sections with careful control. After scraping, we skim-coat any damaged areas and apply a flat primer before the finish coat.
Finish options include smooth (skim-coat level 5), light orange peel, or knockdown texture — all common in Port St. Lucie new construction. The ceiling is painted with two coats of Sherwin-Williams flat ceiling paint as the final step. Everything from scraping through paint is included in one project scope.
Questions Port St. Lucie homeowners ask
Does my older Port St. Lucie home need an asbestos test before popcorn removal? Florida law requires asbestos testing before disturbing any popcorn texture in homes built before 1980. Many older Torino-area homes fall in that range. We coordinate with a licensed asbestos testing lab before scheduling the removal. If asbestos is found, abatement must be completed by a licensed Florida abatement contractor before we proceed — we can refer you to tested local contractors for that step.
Can you remove popcorn ceilings in just one room while leaving the rest of the house intact? Yes, and it’s a common request. We seal off the work area to contain dust, and we can match whatever ceiling texture the rest of your home has when we finish. Many homeowners start with the master bedroom or main living area and schedule additional rooms later.
Popcorn Ceiling Removal — before & after
What Port St. Lucie neighbors say
More services in Port St. Lucie
Get a free estimate in Port St. Lucie
Call (772) 222-3227 or fill out the form. No pressure, line-item quote the same day.
Common questions
How much does popcorn ceiling removal cost in South Florida?
Cost depends on ceiling height, square footage, and condition. Single-story rooms are straightforward; vaulted or two-story ceilings take more setup time. Pre-1980 homes may also require asbestos testing before we can begin — we'll flag that during your free written estimate so there are no surprises.
How long does the process take for a typical home?
Most single-family homes in the 1,500–2,500 sq ft range take two to three days: one day for scraping and drying, one to two days for skim-coating and sanding. High humidity in South Florida means we allow extra dry time between coats rather than rushing — that patience is what keeps the finish from cracking later.
Will the new ceiling hold up in Florida's humidity and heat?
Yes, when it's done correctly. We use moisture-resistant joint compounds suited to South Florida's climate, and we prime with Sherwin-Williams products before any topcoat. Our 5-year workmanship warranty covers the finished ceiling, so if anything shifts or cracks due to our work, we come back and make it right.
